| Soekris: no boot after power loss | ||
|---|---|---|
 | Part IX. OpenBSD |  |
| Soekris: no boot after power loss | ||
|---|---|---|
| | Part IX. OpenBSD | |
So we've got this Soekris Net5501 board, which after power loss shows on the serial link:
comBIOS ver. 1.33b 20080501 Copyright (C) 2000-2008 Soekris Engineering.
net5501
0512 Mbyte Memory CPU Geode LX 500 Mhz
Pri Mas SILICONSYSTEMS INC 4GB LBA Xlt 1023-128-63 4125 Mbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15
0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15
1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 pci mem[639K 511M a20=on]
disk: hd0+*
>> OpenBSD/i386 BOOT 3.02
open(hd0a:/etc/boot.conf): Unknown error: code 102
boot>
booting hd0a:/bsd: open hd0a:/bsd: Unknown error: code 102
failed(102). will try /bsd
boot>
booting hd0a:/bsd: open hd0a:/bsd: Unknown error: code 102
failed(102). will try /bsd
Turning timeout off.
boot>
reboot
Rebooting...
exit
POST: 012345689bcefghips1234ajklnopqr,,,tvwxy
comBIOS ver. 1.33b 20080501 Copyright (C) 2000-2008 Soekris Engineering.
net5501
0512 Mbyte Memory CPU Geode LX 500 Mhz
Pri Mas SILICONSYSTEMS INC 4GB LBA Xlt 1023-128-63 4125 Mbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15
0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15
1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 pci mem[639K 511M a20=on]
disk: hd0+
>> OpenBSD/i386 BOOT 3.02
switching console to com0
>> OpenBSD/i386 BOOT 3.02
boot>
booting hd0a:/bsd: 6039964+1059784 [52+336688+318896]=0x7657ec
entry point at 0x200120
[ using 656008 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2009 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 4.5 (GENERIC) #1749: Sat Feb 28 14:51:18 MST 2009
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 536440832 (511MB)
avail mem = 510427136 (486MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/80/01, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address 00:00:24:cb:9f:d8
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063, model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address 00:00:24:cb:9f:d9
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063, model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address 00:00:24:cb:9f:da
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063, model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address 00:00:24:cb:9f:db
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063, model 0x0034
glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 0, 32-bit 3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SILICONSYSTEMS INC 4GB>
wd0: 1-sector PIO, LBA, 4029MB, 8251488 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 15, version 1.0, legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask e5c5 netmask ffe5 ttymask ffff
mtrr: K6-family MTRR support (2 registers)
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
Automatic boot in progress: starting file system checks.
/dev/rwd0a: 2320 files, 17051 used, 241780 free (20 frags, 30220 blocks, 0.0% fragmentation)
/dev/rwd0a: MARKING FILE SYSTEM CLEAN
/dev/rwd0f: 1 files, 1 used, 259894 free (14 frags, 32485 blocks, 0.0% fragmentation)
/dev/rwd0f: MARKING FILE SYSTEM CLEAN
/dev/rwd0e: 3 files, 3 used, 65396 free (28 frags, 8171 blocks, 0.0% fragmentation)
/dev/rwd0e: MARKING FILE SYSTEM CLEAN
/dev/rwd0g: 14190 files, 228924 used, 890051 free (171 frags, 111235 blocks, 0.0% fragmentation)
/dev/rwd0g: MARKING FILE SYSTEM CLEAN
/dev/rwd0d: 523 files, 3110 used, 256785 free (65 frags, 32090 blocks, 0.0% fragmentation)
/dev/rwd0d: MARKING FILE SYSTEM CLEAN
setting tty flags
pf enabled
net.inet.carp.preempt: 0 -> 1
starting network
starting system logger
starting initial daemons: ntpd.
savecore: no core dump
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sendmail inetd sshd.
starting local daemons:.
standard daemons: cron.
Mon Mar 16 19:45:07 CET 2009
OpenBSD/i386 (hostname) (tty00)
login:
| |  | |
| Redundant firewalling on OpenBSD: bridging mode |  | Home gateway using OpenBSD and PF |